|
|
|
Grommets & Floor Boxes
|
|
For location on a desk or counter. Designed to allow one patchcord through & to house the patchcord before use. The grommet lid has a clip on the underside that allows the patchcord to be hooked on. The grommet requires a 30mm diameter hole and can acommodate a solid 25mm conduit for a fixed installation if required. Ideal for chip and pin installations. |
|
Consists of an outer flange and a central insert. the outer flange fits into an 45mm hole. The overall diameter of the grommet is 62mm. The central hole is 15mm diameter.
|
|
Consists of an outer flange and a two part insert. the outer flange fits into an 80mm hole. Cable are then passed through and the insert fitted with the appropriate quantity of holes exposed.
Standard Colour : Grey or Black |
|
Consists of an outer flange and a two part insert. The outer flange fits into an 95mm hole. Cables are then passed through and the insert fitted with the appropriate extent of slot revealed
Standard Colour : Grey or Black
|
|
Consists of an outer flange and a two part insert. the outer flange fits into an 127mm hole. Cables are then passed through and the insert fitted. Available with either three holes of a slot.
Standard Colour : Grey or Black
|
|
Consists of an outer flange and a two part insert. the outer flange fits into an 170mm hole. Cables are then passed through and the insert fitted. The slot is 35mm deep and approx 130mm long.
Standard Colour : Black
|
|
Consists of an outer flange with overal diameter of 233mm and requires a 209mm cutout. the central section is removable and has four available holes each 28mm diameter.
Standard colour : black
|
|
A rectangular grommet with external dimension 237 x 109mm requiring a cutout 205 x 91mm. Provided with a removable central section complete with four hole with shutter each 26mm wide with a maximum reveal 30mm deep. |
|
Consists of an outer flange and a two part insert. the outer flange fits into an 127mm hole. Cables are then passed through and the insert fitted c/w fixing lugs.
Standard Colour : Black
|
|
The hive is a complex product providing the facility to lock into the floor panel. Providing a foam packaged passage for cable to access the void below. Available in two sizes 127mm & 210mm.
Standard Colour - Grey
From £26.00 £31.20 (incl VAT)
|
|
|
|
Circular floor boxes with internal plate options to fit data or power devices. |
|
A number of 2, 3 & 4 compartment boxes with combinations of power, data and blank spare sections |
|
The air-guard GTAG1 provides a cableway 230 x 65mm and assists optimising the thermal management of the data room plenum through the raised floor installation. This device has a removeable section to allow easy cable release. |
|
The air-guard GTAG2 provides a maximum cableway 180 x 120mm through an upper brush and lower gasket section. It fits into a 230 x 175mm opening in the raised floor. The unit comes with a safety cover which can be removed when cables are installed. |
|
The air-guard GTAG3 provides a cableway 200 x 200mm. Unlike the GTAG1 this unit sits upon the raised floor so is ideal when retrofitting existing holes upto 200 x 200mm. This unit can also be use as two seperate perimeter seals.
|
|
The air-guard GTAG4 provides a cableway 80 x 80mm and assists optimising the thermal management of the data room plenum through the raised floor installation. This device has a removeable section to allow easy cable release. |
|
The GTAG5 AIR GUARD Kit is designed to fit into both new and existing non standard cut outs using brush seal technology.
two sizes are available - see range
From £48.75 £58.50 (incl VAT)
|
|
|
|
The GTAG6 is a grommet with two seperate channel to alllow cable to be segregated within one grommet. This device is a two section grommet allowing easy instalation of the cable. |
|
The Airguard GTAG9 is ideal for siting at the perimeter of a raised floor. It provides a cableway 535mm x 135mm.
Can be used as a pair in a non-perimeter installation. |
|
This is a two part triangular shaped grommet that is ideal for fitting at the edge of a floor. The grommet is 110mm across each flat. The central triangular lid is an equalateral triangle with edge 75mm long with three break out holes however could be cut to any size required. |
|
A solid grommet for a new cable installation, providing a 203 x 102mm cable hole.
Used to reduce airflow from the floor void by offering a form of seal. |
|
A split grommet for a new or retrofit cable installation, providing a 203 x 102mm cable hole.
Used to reduce airflow from the floor void by offering a form of seal.
|
|
A raised grommet for a new or retrofit cable installation, providing a 203 x 102mm cable hole.
Used to reduce airflow from the floor void by offering a form of seal.
|
|
|
|
|
|
Terms & Conditions | Privacy
Site Map |
|
 |
